Hook up bathroom faucet

How to install a bathroom faucet?

How to Install a Bathroom Faucet. If you’re replacing an old faucet, you’ll need to begin by removing it. Turn off the shut-off valves that serve the faucet’s supply tubes. Use a wrench to remove the supply tubes’ nuts from the faucet tailpieces. Place a bucket below the supply tubes; they’ll be filled with water,...

Is it hard to hook up a shower or tub faucet?

Hooking up a shower or tub faucet isnt as difficult as you might think. So long as youre comfortable with accurately measuring, drilling, and working with copper pipe, this project is well within reach. We broke the installation process down into easy-to-follow steps for optimal ease.

How high should a faucet be above a bathtub?

How to Install a Shower or Tub Faucet. Follow the manufacturers directions for plumbing the faucet. And, if your faucet does not have integrated shutoff valves, install shutoff valves in the lines to the valve. For optimal comfort, position the faucet about 28 inches above the floor for a tub, and about 48 inches for a shower.

Do you Mount the faucet before or after the sink?

If youre installing a new sink along with your faucet, mount the faucet to the sink before you install the sink. Its much simpler than lying on your back inside the sink cabinet to install the faucet.

How do I install a new kitchen faucet?

Follow the manufacturer’s directions for installation. Our faucet is centerset. Put the gasket on first. Then insert the faucet through the mounting holes and tighten the nuts. Next, install the drain body and rubber washer through the top of the sink. Apply a bit of silicone between the rubber gasket and the bottom of the sink.

How to replace a bathroom faucet?

1 Gather your tools and supplies. Replacing a bathroom faucet is a straightforward job, but it does require a few tools that youll need to remove the old faucet and ... 2 Prepare your work area. Remove everything from underneath the sink. ... 3 Turn off the water. Locate the water shutoff valve for the bathroom sink. ... 4 Drain the water. ...

How do you attach a lift rod to a kitchen faucet?

Next, insert the lift rod into the faucet. Connect the lift rod to the lift rod strap by pushing the button. Then, make sure the ball rod is in the down position and attach the lift rod strap to the ball rod. Before setting the sink into place, connect the supply lines to the faucet shanks.

How do you fix a leaky faucet that wont drain?

Apply a bit of silicone between the rubber gasket and the bottom of the sink. Secure it with the lock nut. Clean up excess silicone with mineral spirits. Insert the ball rod into the drain assembly and tighten the sleeve. Next, insert the lift rod into the faucet. Connect the lift rod to the lift rod strap by pushing the button.

Tub Spout Height Above Tub (How High Should Tub Spout Be Above Tub?) As a general rule, therefore, you should try to place a bath-only spout somewhere around 4 inches above the rim of the tub on the low side and 12 to 18 inches on the higher side.

How far should a faucet be from the sink?

Do you Mount the faucet to the sink or cabinet?

Premount the Faucet on New Sink Installations If youre installing a new sink along with your faucet, mount the faucet to the sink before you install the sink. Its much simpler than lying on your back inside the sink cabinet to install the faucet.

How long should I wait to install faucets after sink installation?

The installer recommends waiting 48 hours after sink installation to install faucets and reconnect all of the plumbing. Is there any wiggle room in this time frame? I have someone who can come reconnect all of my plumbing approx 40 hours after install. Will the 8 hours make a difference?

Is it easier to replace a faucet from inside or outside?

Its much simpler than lying on your back inside the sink cabinet to install the faucet. Even if youre not installing a new sink, you may find it easier to remove the old sink to get better access for removing the old faucet and installing the new one.

How do you install a new faucet gasket?

STEP 1: Install the sink gasket. Before a new faucet is attached, a seal is needed between the faucet and the sink. Some new faucets come with a plastic or rubber gasket. If not, you can make a snake from plumber’s putty and put it on the sink where the faucet will sit.