Car amplifier hookup

How to connect a car stereo to a car AMP?

Connect the remote power wire from the stereo to the amp, and the RCA cable is also connected here. After the set, the RCA to the head unit and remote power wire to the amp set the speaker wire to the speaker of your car.

Where should I install an amplifier in my car?

Good locations to install an amplifier include: Pros: You can use short wires and patch cords. You wont have to remove a seat or climb into the trunk. Cons: Only very small amps fit here. This puts your amp close to some common noise sources. Pros: Plenty of room for large amps. Near the rear speakers. Easy access to the amp controls.

How do you hook up a subwoofer to a car?

Connect the front, rear, and subwoofer speaker wires from the amplifier to the corresponding speakers. 5. Run the power lead from the amp (ensuring that its on the opposite side of the car to your RCA cables) through the hole in the firewall and to the battery.

How to connect RCA speaker to car amplifier?

After the set, the RCA to the head unit and remote power wire to the amp set the speaker wire to the speaker of your car. When you will get your RCA attached to the head unit and speaker wire, and ground cable and the main power cable on the carpet, hook the amplifier and turn on.

Can you plug a car AMP into a car stereo?

Car stereos aren’t designed to be bridged like a car amp. Using an ATX (desktop computer) power supply for a car stereo isn’t hard – in fact, you only need a few steps: Power connections: Cut a +12V wire (yellow) and a ground (black) wire from the main connector. Strip the insulation to leave about 3/8″ to 1/2″ bare wire.

How to wire a computer power supply to a car stereo?

How to wire a computer power supply to a car stereo Using an ATX (desktop computer) power supply for a car stereo isn’t hard – in fact, you only need a few steps: Power connections: Cut a +12V wire (yellow) and a ground (black) wire from the main connector. Strip the insulation to leave about 3/8″ to 1/2″ bare wire.

How do you hook up a car radio to power?

1 Ground: Connect the radio’s ground wire (black wire) to the (-) power supply output 2 Main power: Connect the radio’s +12V battery wire (usually the yellow wire) to the (+) power supply output 3 Turning the radio on: You can do this by hardwiring the radio’s accessory wire (usually red) to the +12V battery wire or you can use a switch in between.

How do you wire a car AMP to a speaker?

Disconnect or cut the factory speaker wires and connect the new wires directly to each speaker terminal. It is important that you keep the polarity of your speaker wiring straight. This means that each positive terminal of the amp connects to a positive terminal of a speaker — and the same goes for the negative terminals.

How to connect RCA cables to car speakers?

An amp is crucial to connecting RCA cables to car speakers successfully. The main connection between the RCA cables and the speaker will come from the amp’s socket. In many cases, most cars come with speakers that have inbuilt amplifiers. But, if your car speaker doesn’t have an amplifier, you’ll need to install one.

How to connect a car AMP to a full-range RCA output jack?

Full-range RCA output jacks can be connected directly to the car amp’s RCA inputs. In all cases, you’ll also need to wire the amp with power and a remote-on wire so it can turn on. You can do this one of several ways:

How do I Connect 2 speakers to a car AMP?

Most car amps with front & rear speaker level inputs can be wired to 2 speaker input pairs as shown in the diagram here. When using RCA connections, you can pick up a pair of inexpensive female-to-male Y adapters to split the signal from 2 into 4 connections.

Can I use a car AMP for home stereo?

The amp’s speaker level inputs will scale down the speaker inputs to a low signal it can use. Home stereo with no RCA output jacks + car amp with RCA jack inputs only: In this case, you’ll have no choice but to use a line level converter commonly used for car audio.