Hook up wheels

How do I install the front wheel on my bike?

When installing the front wheel, simply slide the axle evenly up into the fork dropouts, with the quick release lever on the left side of your bike. Holding the cap with one hand, spin the lever clockwise, making sure the side marked ‘Open’ is facing outwards.

How to remove and install your wheels?

How to Remove and Install Your Wheels 1 Remove Front Wheel. When removing the front wheel, the first step is to disconnect your brake. ... 2 Install Front Wheel. You should always remember to apply a thin layer of grease along the entire length of your skewer rod. 3 Remove Rear Wheel. ... 4 Install Rear Wheel. ... 5 Recommended Tools 6 Categories

How do you put the chain back on the rear wheel?

Install Rear Wheel To re-install the rear wheel, first place the chain back onto the smallest sprocket, and then slide the axle evenly up into the rear dropouts. Tighten the quick release lever the same way as the front wheel, with the lever on the left side of the bike. Make sure the lever is safely tucked in between both of the left chain stays.

How do I install the front wheel Springs?

The springs are only designed to provide clearance while removing and installing your wheel. You should always remember to apply a thin layer of grease along the entire length of your skewer rod. When installing the front wheel, simply slide the axle evenly up into the fork dropouts, with the quick release lever on the left side of your bike.

How do I install the front wheel?

It is often easiest to install the front wheel when the bike is standing. This lets you push down to ensure that the axle is fully inserted in both sides of the fork so that the quick-release skewer can fully engage the dropout surfaces. 1. Check that the quick-release lever is in open position.

How do you install a dirt bike?

Similar to a pedal bike, the front wheel installs by squeezing past the brake pads, slipping onto the forks then tightened. However, a dirt bike has a removable axle that fits inside the hub and connects both sides to the forks via axle lugs at the end of the forks. You need to align this axle before fully installing the wheel.

How does a dirt bike front wheel fit?

Similar to a pedal bike, the front wheel installs by squeezing past the brake pads, slipping onto the forks then tightened. However, a dirt bike has a removable axle that fits inside the hub and connects both sides to the forks via axle lugs at the end of the forks.

How do I re-install the rear wheel on my bike?

To re-install the rear wheel, first place the chain back onto the smallest sprocket, and then slide the axle evenly up into the rear dropouts. Tighten the quick release lever the same way as the front wheel, with the lever on the left side of the bike.

Step 1: Prepare your bike. Step 2: Check out your drive chain. Step 3: Loosen the chain. Step 4: Let go of the derailleur. Let’s get into details! What Are Chains and the Derailleur? Before delving into putting a bike chain back on a derailleur, it would be better to understand bicycle chains and derailleurs.

How do I remove the chain from the rear wheel?

How do you install a rear axle spring?

Attach the spring to the rear bracket. Fit the other end of the spring in the square-shaped bracket at the back end of the wheel. Replace the eye bolts and nuts, tightening them until the spring is suspended in place. Install the U-bolts and shock pad. Hang the U-bolts over the axle, 1 on each side of the spring.

How do you attach a wheel spring to a bracket?

Attach the spring to the rear bracket. Fit the other end of the spring in the square-shaped bracket at the back end of the wheel. Replace the eye bolts and nuts, tightening them until the spring is suspended in place.

How to replace coil springs on a car?

Then, slip the strut out of position and away from the car. Keep all the nuts safe so that you can use them to replace the new parts. Coil springs don’t come with replacement nuts. To remove the coil from the strut you must, above all, observe safety. The coil springs must be compressed before you undo the bolt at the top of the strut.

How do you install a lower control arm spring?

Install the spring. Since lowering springs are made to work with your factory suspension, you will just put the new lowering spring in the same place as the old coil spring. Fasten it in the same way as the old coil spring before reattaching other hardware. Use the jack to raise the lower control arm.