Pool sand filter hook up

How do I connect my sand filter to my pool pump?

There are 3 hoses for you to connect when installing your sand filter. The first hose connects from the thru-wall skimmer on the pool to the front of the pump, also known as the strainer housing. On the skimmer there should be a fitting where the hose will connect.

How do you connect a pool hose to a filter?

Hose #1. The first hose connects from the thru-wall skimmer on the pool to the front of the pump, also known as the strainer housing. On the skimmer there should be a fitting where the hose will connect. Loosen the clamps that came with the filter and slide them over the hose ends.

How do you backwash a pool with a sand filter?

Connect the other end of this hose to the inlet port on the side of your pool. Turn on the pump’s circuit breaker. Move the lever on the sand filter to the “backwash” position. Turn on the above-ground pool pump. Allow the pump to run for about two minutes to remove any impurities from the silica sand in the filter.

How many hoses do I need to install a sand filter?

There are 3 hoses for you to connect when installing your sand filter. The first hose connects from the thru-wall skimmer on the pool to the front of the pump, also known as the strainer housing.

How do I install a sand filter on my Pool?

There are 3 hoses for you to connect when installing your sand filter. The first hose connects from the thru-wall skimmer on the pool to the front of the pump, also known as the strainer housing. On the skimmer there should be a fitting where the hose will connect. Loosen the clamps that came with the filter and slide them over the hose ends.

How do I connect the hose to my sand filter?

How to Connect Hoses to your Sand Filter. 1 Hose #1. The first hose connects from the thru-wall skimmer on the pool to the front of the pump, also known as the strainer housing. On the skimmer ... 2 Hose #2. 3 Hose #3.

How do you connect a pool pump to a filter?

How to Connect a Filter & Pump for a Swimming Pool Step 1. Place the pump and filter assembly on level ground next to the electric source. Make sure the pool filter and... Step 2. Connect the pump to the filter housing. Apply plumbers tape at the point of connection to prevent leaking. Step 3. ...

How do you connect a pool filter to a skimmer?

Connect the hose from the skimmer to the filters pump basket. Use the same technique in connecting the skimmer/pump basket hose as you did when connecting the hose from the return to the filters out port. Loosen the lid on the filter pump basket.

This normally takes between 1 minute and 3 minutes, depending on how dirty the filter was. Do you rinse after backwashing a pool? Once I have turned the pump off I always turn the multiport valve to Rinse and run the pump again for between 30 seconds and a minute.

Why do I need to backwash my sand filter?

How do I install a sand filter on my Pool?

There are 3 hoses for you to connect when installing your sand filter. The first hose connects from the thru-wall skimmer on the pool to the front of the pump, also known as the strainer housing. On the skimmer there should be a fitting where the hose will connect. Loosen the clamps that came with the filter and slide them over the hose ends.

How do I connect the hose to my sand filter?

How to Connect Hoses to your Sand Filter. 1 Hose #1. The first hose connects from the thru-wall skimmer on the pool to the front of the pump, also known as the strainer housing. On the skimmer ... 2 Hose #2. 3 Hose #3.

How much water does a sand filter turn over?

Most Sand Filters turn over approximately 2400 gallons per hour. It is recommended that you turn over the water in your pool at least twice a day (refer to chart at bottom of page for your pools capacity). Run filter more in hot weather or with heavy bather load.

What is sand sand filter made of?

Sand filters use granular filtering media composed primarily of silica-based minerals such as diatomaceous earth (DE), fossil shell flour, or a mixture of both. The material traps tiny particles, which are then flushed down the drain with normal pool water circulation through the filter.