Hx711 arduino hookup

How do I connect my hx711 to my Arduino?

You wire the load cell wires on one side, and the microcontroller on the other side. The HX711 communicates with the microcontroller using two-wire interface (Clock and Data). You need to solder header pins on the GND, DT, SCK, and VCC pins to connect to the Arduino.

What is the hx711 amplifier?

The HX711 amplifier is a breakout board that allows you to easily read load cells to measure weight. You wire the load cell wires on one side, and the microcontroller on the other side.

How to calibrate hx711 load cell measurement with Arduino?

How to calibrate HX711 Load cell measurement with arduino ? Once you upload the calibration code, open serial monitor and adjust your scale factor with known weight until you see the correct readings. Press a,s,d,f to increase calibration factor by 10,100,1000,10000 respectively.

How to interface the Avia semiconductor hx711 24-bit analog-to-digital converter (ADC) with Arduino?

An Arduino library to interface the Avia Semiconductor HX711 24-Bit Analog-to-Digital Converter (ADC) for reading load cells / weight scales. This library is compatible with the architecture. To use this library, open the Library Manager in the Arduino IDE and install it from there.

How do I connect the hx711 amplifier to Arduino?

You need to solder header pins on the GND, DT, SCK, and VCC pins to connect to the Arduino. I soldered the load cell wires directly to the E+, E-, A-, and A+ pins. The load cell wires were very thin and fragile, be careful when soldering to not damage the wires. For more information about the HX711 amplifier, you can consult the HX711 datasheet.

How many wires are there in a hx711?

All controls to the HX711 are through the pins. Most Load cell have four wires red, black, green and white. On HX711 board you will find E+, E-, A+, A- and B+, B- connections.

How to calibrate hx711 load cell measurement with Arduino?

How to calibrate HX711 Load cell measurement with arduino ? Once you upload the calibration code, open serial monitor and adjust your scale factor with known weight until you see the correct readings. Press a,s,d,f to increase calibration factor by 10,100,1000,10000 respectively.

How to interface the Avia semiconductor hx711 24-bit analog-to-digital converter (ADC) with Arduino?

An Arduino library to interface the Avia Semiconductor HX711 24-Bit Analog-to-Digital Converter (ADC) for reading load cells / weight scales. This library is compatible with the architecture. To use this library, open the Library Manager in the Arduino IDE and install it from there.

What is an Arduino hx711 24-bit analog-to-digital converter?

An Arduino library to interface the Avia Semiconductor HX711 24-Bit Analog-to-Digital Converter (ADC) for reading load cells / weight scales. This library is compatible with the architecture.

What is the best library to interface hx711 with Arduino?

HX711 library 2 GitHub - bogde/HX711: An Arduino library to interface the Avia Semiconductor HX711 24-Bit Analog-to-Digital Converter (ADC) for Weight Scales. GitHub - bogde/HX711: An Arduino library to interface the Avia Semiconductor HX711 24-Bit Analog-to-Digital Converter (ADC) for Weight Scales.

What is Avia hx711 library?

Library to interface the Avia Semiconductor HX711 ADC. An Arduino library to interface the Avia Semiconductor HX711 24-Bit Analog-to-Digital Converter (ADC) for reading load cells / weight scales. This library is compatible with the architecture.

How many hx711 for 24 bit ADC?

This 24 BIT ADC has 2 differential inputs for 2 load cells. In the end I need 4 load cells so that means the use of 2 x HX711.