700r4 speedometer hookup

Can you convert a 700R4 to an electric Speedo?

Perfect for street or hot rod applications. This kit will convert your 1980s or early 1990s 700R4 / 4L60 electric speedo setup back to the original mechanical setup so you can get a proper speedometer reading on your older vehicle.

Can you wire an electric speedometer to a R4 electrical?

Wiring Electric Speedometer to r4 Electrical. I robbed the connector that plugs into it at the pull-a-part salvage. Its just a 2 wire connection. TCI® now stocks the most popular speedometer gears. Note: Drive gear refers to the Speedometer gears: R | TH | TH | R4 | Torqueflite | Ford.

Can a 700R4 be converted to mechanical?

CT8767 - Everything needed to convert your 700R4 / 4L60 transmission speedo setup from electric to mechanical. Perfect for street or hot rod applications. This kit will convert your 1980s or early 1990s 700R4 / 4L60 electric speedo setup back to the original mechanical setup so you can get a proper speedometer reading on your older vehicle.

Where does the Speedo plug go on an R4?

Feb 09, · if the speedo plug is a 2 wire hook up on your R4 one wire goes to ground the other goes to the signal in post of the electronic speedo. You will have to use the calibration button that came with your speedo. I have a 85 corvette r4 and a new SW wings series electronic speedo .R4 - Can you idnentify this wire / plug?

Can a 700R4 be converted to mechanical?

How to tell if a Speedo gear is 700R4?

You can find the cover w/the o ring around it (it cant think of what its called) for larger speedo gears on older 3/4 ton Chevy p/us that have 700r4s still in them. (42,43,44 tooth count) Also on 86-92 Z28,but bring a stiff brush to get gerase/dirt mix off and look at the numbers on the cover thing.700r4s only not on 4l60es.

How to install a speedo on a TH700R4?

Very simple actually, all you need is a mechanical speedo bullet, drive gear and clip (on output shaft), and driven gear. (fits in bullet) There were mechanical speedos in some older TH700R4s from the factory. The hard part is removing the old reluctor from the output shaft.

How to use 57 Chevy cable speedometer with a R700 Trans?

What is the simple solution to using an original 57 chevy cable speedometer with a R700 trans. that has an electronic speedometer on the tailshaft?? You unbolt and remove the tail housing. There is a round disc (reluctor wheel) with notches on the out put shaft. Remove that disc. Should be holes in the output shaft, the disc covered.

How hard is it to replace a Speedo gear housing?

The job isn’t all that difficult, but you can have complications if the speedo gear housing is corroded in the transfer gearbox casing. Its advisable to soak the area in a penetrating oil a day before you plan on doing the job. So for this job you will need: Sturdy screwdriver or chisel WD40 or other penetrating oil 10mm spanner/socket

How to install a speedo on a TH700R4?

Where is the speedo drive gear on a Toyota Corolla?

Access:The speedo drive gear is located at the back of the transfer gearbox in front of the handbrake drum. You can access it from underneath the vehicle, but it is easier to remove the middle seat (or cubby box) and get to it by removing the cover from inside the car.

Why is my Speedo not working on my Land Rover?

If it doesn’t fix your problem, (like on mine) then you need to check the speedo drive gear is actually turning the inside of the new cable. To do this you disconnect it at the speedo end and just secure it in view. Then drive the Land Rover for a few yards down the road.